ParaTank_215 5" race quad with swappable arms.

Slightly beefier than typical race frames but still at only 66g with awesome CG (top or bottom mount optional), slotted arms, cam protection (runcam micro type) and super low body and arm profile for minimum air resistance and loss of thrust... Also with printable arm tpu arm protectors+motor softmounts (And it looks cool) :D

Please note that you will need to cut two of the included standoffs to length. 2x 19mm.
I very much wish this wasn't necessary, but very unfortunately, armattan doesn't have those lengths available...

The arm / motor protectors are available here: https://www.thingiverse.com/thing:2678821

Rcgroups discussion here: https://www.rcgroups.com/forums/showthread.php?2996166-ParaTank_215-5-RaceQuad-with-swappable-Arms-Arm-Protection

Some more pictures:

This kit is for what I call the Muscle Para-hex, which is a mix of my parakeet and my tanky frame designs.

It is set up for 1306 - 1806 Motors (and similar ones), and meant to spin 4" props.

Bottom or Top Mount are optional.

The camera protection plates are designed to hold Runcam MicroSwift or Caddx Micro and similar cameras.

Please note that you will need to cut the included standoffs to length. 4x 18mm, 2x 19mm.
I very much wish this wasn't necessary, but very unfortunately, armattan doesn't have those lengths available...

The arm / motor protectors are available here: (link soon)

some more pictures below:

This custom top is made to fit the default main-plate for the RotorX Raiju RX155 (meaning you won;t have to drill any holes), and is intended for cameras of the Runcam Swift Micro Format (19x19mm).

Thanks to the structural setup, impact forces will be nicely distributed among all 6 standoffs. All plates are 2mm thick, making the custom top very crash resilient and tanky. -- And I think it looks cool.

It is intended for 4x 20mm and 2x 10mm standoffs (as included in this kit). It also required 3-4 (4rth is optional) horizontal standoffs at 19mm. Unfortunately armattan productions does not carry these at the moment, so you'll have to cut the included 24mm standoffs to length (or supply your own standoffs).

Also please note that this is designed to be very tight and snuck, so depending on whether armattan's mill has a good or a bad day, you may have to do some very slight filing of edges. In general, however, this should not be an issue.

You can also source each of the components by themselves if you already have fitting standoffs/screws. Just click on the listed items and purchase them individually. One full kit consists of 1x topplate, 1x bottomplate, 2x sideplates.

A couple of pictures for reference (including 3D printed prototypes - which were slightly improved since).

Can find the files for download (noncommercial) here on amattan or on thingiverse: https://www.thingiverse.com/thing:2576432

My Shop with full list of products (click here)!

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This frame is the parakeet NOx32 special stretched deadcat for 140X motors, 4" props and a 4mm thick baseplate. 

Since Armattan does not provide standoffs in the correct lengths, you'll have to cut the 24mm ones to 19mm to fit the swift micro protector and the 15mm ones to 14mm. Everything else *should* fit nicely, but you may need to do a tiny bit of filing to make everything slot perfectly.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License

This frame is the parakeet NOx32 special stretched deadcat for 110X - 140X motors, 3" props and a 4mm thick baseplate. 

Since Armattan does not provide standoffs in the correct lengths, you'll have to cut the 24mm ones to 19mm to fit the swift micro protector and the 15mm ones to 14mm. Everything else *should* fit nicely, but you may need to do a tiny bit of filing to make everything slot perfectly.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License

This is the top-plate + cam protection sides + standoffs kit for the parakeet ecosystem.

Please note: As armattan cannot cut 90 deg. angled perfectly, you will have to do 1min of filing the edges where the sideplates slot into the main and topplate. Also, armattan does not provide the required 19mm and 18mm standoffs. Accordingly, you will have to cut the included 24mm standoffs to size.

Shop with full list of products (click here)!

more soon

This kit is the TANKY Runcam Micro Swift Pod for the 20x20mm hardware frames as listed below. It will perfectly fit the Micro Swift. The sides are 2mm, the bottom plate is 3mm strong.

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) The Runcam MicroSwift is exactly 19mm wide, which this pod accomodates. Armattan Productions does not provide this length standoff. This kit includes 24mm standoffs which you will have to grind/cut to size!

b) You will have to sand a bit of carbon fibre away where the bottom plate meets the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This kit is the MEDIUM Runcam Micro Swift Pod for the 20x20mm hardware frames as listed below. It will perfectly fit the Micro Swift. The sides are 1.5mm, the bottom plate is 2mm strong.

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) The Runcam MicroSwift is exactly 19mm wide, which this pod accomodates. Armattan Productions does not provide this length standoff. This kit includes 24mm standoffs which you will have to grind/cut to size!

b) You will have to sand a bit of carbon fibre away where the bottom plate meets the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This is a pod for a 20x20mm stack at 45° FC rotation. It is not designed for any of the current frames in my shop.

It still requires the following:

• 3D printed Cam bracket. The cam snaps in place and with 2 m2 screws one can adjust the desired angle. Available here: https://www.thingiverse.com/thing:2353291/
• 10 M2 nylon screws (for standoffs and cam holder)
• 3 15mm M2 nylon standoffs
• Armattan productions cannot fit everthing *perfectly*, which means, where the bottom plate is pushed into the side plates you may have to do a little bit of filing of the CF (under running water!) to give it a perfect fit.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License

This kit is the Runcam Micro Swift Pod for the 20x20mm hardware frames as listed below. It will perfectly fit the Micro Swift. The sides are 1mm, the bottom plate is 2mm strong.

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) The Runcam MicroSwift is exactly 19mm wide, which this pod accomodates. Armattan Productions does not provide this length standoff. This kit includes 24mm standoffs which you will have to grind/cut to size!

b) You will have to sand a bit of carbon fibre away where the bottom plate meets the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This is a pod for the 16x16mm hardware frames available in my shop.

It still requires the following:

• 3D printed Cam bracket. The cam snaps in place and with 2 m2 screws one can adjust the desired angle. Available here: http://www.thingiverse.com/thing:2248569
• 10 M2 nylon screws (for standoffs and cam holder)
• 3 15mm M2 nylon standoffs
• Armattan productions cannot fit everthing *perfectly*, which means, where the bottom plate is pushed into the side plates you may have to do a little bit of filing of the CF (under running water!) to give it a perfect fit.

Links and more about the frames here:

These frames have been designed for 16x16mm fc hardware (uses M2 screws!) and 0703/0806 brushless motors (different mountings!) and come in various sizes to provide the smallest possible frame for the respective motor and prop size.

~ !Note that 0703 and 0806 Motors use completely different mounting holes! Which means these are not interchangable. Make sure you choose the correct frame! ~

As armattan productions hardware does not feature M2 hardware, you will have to get the nylon screws and standoffs yourself.

This frame is available in the following formats:

0703 Motors:

• Micro 56 for 0703 motors and 31mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7427
• Micro 62 for 0703 motors and 40mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7428
• Micro 68 for 0703 motors and 45mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7429
• Micro 76 for 0703 motors and 2" props (2mm thick): https://armattanproductions.com/pages/product_details/7430
• Micro 80 for 0703 motors and 56mm props (2mm thick): https://armattanproductions.com/pages/product_details/7431

0803 Motors:

• Micro 56 for 0806 motors and 31mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7432
• Micro 62 for 0806 motors and 40mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7433
• Micro 68 for 0806 motors and 45mm props (1.5mm thick): https://armattanproductions.com/pages/product_details/7434
• Micro 76 for 0806 motors and 2" props (2mm thick): https://armattanproductions.com/pages/product_details/7435
• Micro 80 for 0806 motors and 56mm props (2mm thick): https://armattanproductions.com/pages/product_details/7436

The frames have been designed with the latest generation of aio cam+vtx in mind (15mm width). You have two options to mount these cameras:
A) a minimalistic tiny-whoop style cam holder without much protection
B) a 1mm carbon fibre pod with m2 nylon standoffs which allows you to change the angle and protects the cam

Links to the cam options:

• Minimalistic tiny-whoop style cam holder on thingiverse: http://www.thingiverse.com/thing:2248569
• Carbon fibre pod with adjustable angle + protection: https://armattanproductions.com/pages/kit_detail/926

List of potential hardware:

• tinyFISH FC: http://fishpepper.de/projects/tinyfish/
• tinyPEPPER 4in1 ESC: http://fishpepper.de/projects/tinypepper/
• Eachine EF-02 AIO 5.8G 40CH 25MW VTX: http://www.banggood.com/Eachine-EF-02-AIO-5_8G-40CH-25MW-800TVL-VTX-13-Cmos-FPV-Camera-p-1119217.html
• Frsky ultra light RX: http://www.banggood.com/FrSky-XM-2_4G-16CH-Telemetry-Receiver-p-1107435.html
• Gemfan 0806 motors: http://www.banggood.com/3B-R-0806-6200KV-7500KV-2S-FPV-Racing-Brushless-Motor-for-RC-Multicopters-p-1138409.html
• Nylon standoff set: www.banggood.com/120pcs-M2-Nylon-Hex-Spacers-Screw-Nut-Assortment-Stand-off-Accessories-Set-Kit-p-998985.html
• etc.

Some concept pictures:

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License

This frame is the Runcam Swift Mini Pod for the 20x20mm hardware frames as listed below. It will perfectly fit the Swift Mini with small and larger lense (as well as a runcam owl with an adapter from thingiverse). The sides are 2mm, the bottom plate 3mm strong, making this a very study pod.

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) The Runcam Swift Mini is exactly 22.3mm wide, which this pod accomodates. Armattan Productions does not provide this length standoff. This kit includes 24mm standoffs which you will have to grind/cut to size!

b) You will have to sand a bit of carbon fibre away where the bottom plate meets the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This frame is the Minimalist Full Sized CCD camera pod for the 20x20mm hardware frames as listed below. It will perfectly fit, for example, a Runcam Owl Plus, Runcam Swift, HS1177 and pretty much any other similar camera.

This minimalistic pod does provide protection from above, but not if you manage to fly into a horizontal bar. 

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) This design is using grub screws / threaded rods to connect the frame with the pod. Armattan Productions does not list such screws in their kit possibilities. Accordingly you will either have to source those from somewhere else (e.g. here: banggood, amazon or your local hardware store), or cut/grind off the heads of the 20mm bolts included in this kit.

b) You will have to sand a bit of carbon fibre away where the bottom and top plates meet the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This frame is the Protected Full Sized CCD camera pod for the 20x20mm hardware frames as listed below. It will perfectly fit and protect all around, for example, a Runcam Owl Plus, Runcam Swift, HS1177 and pretty much any other similar camera.

Contrary to just about every other micro-frame, the stand-offs for the Canopy / Pod on this frame and it's siblings are independent of the FC mounting screws, so if you crash, your FC and other electronics  won't be smashed.

Important:

a) This design is using grub screws / threaded rods to connect the frame with the pod. Armattan Productions does not list such screws in their kit possibilities. Accordingly you will either have to source those from somewhere else (e.g. here: banggood, amazon or your local hardware store), or cut/grind off the heads of the 20mm bolts included in this kit.

b) You will have to sand a bit of carbon fibre away where the bottom and top plates meet the side plates. This is because the limitations of Armattan CNC milles. I could have designed things to fit out of the box, but that would have sacrificed some strength which I was not willing to do. I believe 5 minutes of sanding (under running water! you don't want to breath in CF dust!) are worth the effort.

See below for more information about the frame and pods:

QUAD versions:

• Version1: Tanky110 for 1306/1407 motors only (3mm thick): https://armattanproductions.com/pages/product_details/4555
• Version2: Tanky110 for 1104 to 1407 motors variable (2mm thick): https://armattanproductions.com/pages/product_details/5811
• Version3: Tanky110 for 1104 to 1407 motors variable (3mm thick): https://armattanproductions.com/pages/product_details/6743
• Version4: (insane) Toothrip110 for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7354
• Version5: Tanky130_stretched for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7717
• Version6: (insane) Toothrip130_streched for 1306/1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7718

In addition, Cesium FPV has remixed his own stretchbee version:

• Cesium FPV stretchbee for 1104 to 1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7562
• Cesium FPV stretchbee for 1104 to 1407 motors (4mm thick): https://armattanproductions.com/pages/product_details/7563

HEXA versions:

• Version1: Tanky150 for 1306/1407 motors (3mm thick): https://armattanproductions.com/pages/product_details/7476
• Version2: (insane) Toothrip150 for 1306/1407 motors  (4mm thick): https://armattanproductions.com/pages/product_details/7355

In addition to the bottom plates, you can purchase 3 different Pods all of which fit on all 20x20 in the T4b Design store.
Yes that's right, the pods are completely interchangable. So you can toss your own frame salad so to speak.

Cam Pod Versions:

• Version1: CCD Protect pod (added protection) for e.g. Runcam Swift, Owlcam Plus etc. : https://armattanproductions.com/pages/kit_detail/916
• Version2: CCD Simple pod (minimalist) for e.g. Runcam Swift, Owlcam Plus etc.: https://armattanproductions.com/pages/kit_detail/917
• Version3: SwiftMini pod for Runcam SwiftMini (as well as runcam owl + adapter available on thinigverse): https://armattanproductions.com/pages/kit_detail/918
• Version4: MicroSwift pod for Runcam MicroSwift: https://armattanproductions.com/pages/kit_detail/945

(Note: Armattan only carries the most basic of screw/standoff hardware, which means, you may have to source some of the components for the pods yourself or grind the provided hardware to size.)

Alternatively, for the lowest possible profile, you can print a CMOS cam canopy, of which there are 3 versions.

3D Printable Canopies:

• Version1: T4b Design Standard canopy for CMOS: http://www.thingiverse.com/thing:1783281
• Version2: Caesium FPV light canopy for CMOS: http://www.thingiverse.com/thing:2100233
• Version3: Juha FPV increased angle for CMOS: http://www.thingiverse.com/thing:2220820

3D printable protective shoes/motor guards are also available on thingiverse: http://www.thingiverse.com/thing:1783281

A couple of sample / concept pictures of the various frames below

Hardware included in the builds in the pictures:

• 4x stand-offs (10-20mm, depending on your choice of hardware) will be needed to separate canopy and bottom plate.

• 1x Furious Piko BLX FC
  http://furiousfpv.com/product_info.php?products_id=41

• 1x TBS Unify Pro HV
  http://team-blacksheep.com/products/prod:unify_pro_hv_race

• 1x Mini CMOS FPV Camera
  http://www.hobbyking.com/hobbyking/store/__83353__Mini_CMOS_FPV_Camera_1_4_HD_sensor_line_600.html

• 1x MinimOSD Micro
  http://www.hobbyking.com/hobbyking/store/__81598__Micro_Minim_On_Screen_Display_OSD_with_KV_Team_Mod.html

• 1x TBS Crossfire micro receiver
  http://team-blacksheep.com/products/prod:crossfire_mrx

• 4x Littlebee 20A Belheli_S
  http://www.banggood.com/4X-Favourite-FVT-LittleBee-20A-S-ESC-BLHeli_S-OPTO-2-4S-Supports-Mulitshot-Oneshot42-OneShot125-p-1066951.html

• 4x Emax 1306 4000kv
  http://www.banggood.com/4PCS-Emax-RS1306-4000KV-RaceSpec-Motor-2CW2CCW-For-FPV-Racing-p-1068501.html

• 4x Diatone 1408 4100 KV (insane)
  http://www.banggood.com/Diatone-D-Silver-1408-4000KV-Motor-2-4S-CW-Screw-Thread-For-120-150-FPV-Racing-Frame-p-1102894.html

• RotorX 3040 Triblade props
  http://team-blacksheep.com/products/product:831

• 1x 5v micro beeper
  (can't find online link)

• 4x 3mm ulta-bright [insert color] LEDs (pointing backwards)

• 1x 15mm battery strap (I'm using TBS)

• 4x 3mm ultra-bright UV Leds (illuminating the body) (only works with UV fluorescent materials ofc)

All of the listed components could of course be replaced by any other kind of hardware (as long as you can make them fit).

List of other potential hardware:

• frsky micro RX:
  http://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

• BangGood Innova vtx stack clone:
  http://www.banggood.com/Micro-20x20mm-VTX-OSD-Board-40CH-5_8G-25mw-200mw-Mini-FPV-Transmitter-Integrated-OSD-RHCP-p-1107269.html

• BangGood Piko Clone (with potentially better BEC than original Piko):
  http://www.banggood.com/CleanFlight-BetaFlight-Micro-F3-Flight-Controller-Built-in-PDB-Buzzer-20X20mm-For-FPV-Racing-p-1094615.html

• Banggood F3 Micro AIO FC (M2 holes):
  http://www.banggood.com/Mini-20x20mm-PBF3-EVO-6DOF-F3-Flgiht-Contorl-Board-with-MPU6000-SPI-5V-3A-BEC-Support-Soldering-ESC-p-1108332.html?rmmds=myorder

• Emax F3 Micro AIO FC:
  http://www.banggood.com/Emax-STM32F303-F3-Femto-Flight-Controller-with-Integrated-BECBuzzer-PadsVBatPDB-p-1101875.html

• BangGood F3 Micro AIO FC with integrated OSD:
  http://www.banggood.com/Betaflight-3_1-F3-6DOF-Mini-Flight-Controller-20x20mm-Integrated-OSD-Built-in-5V-BEC-p-1119503.html

• BangGood F4 Micro FC:
  http://www.banggood.com/STM32F4-F4-2-4S-Lipo-20x20mm-Mini-Flight-Control-with-BEC-for-Multirotor-p-1111289.html 
   
• And so many more. Just search for 20x20mm and you will find loads of hardware by now

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.