The Lil’ Remix frame is inspired by and serves as a tribute to the 5 inch Remix designed by Tommy Tibajia and manufactured by Rotor Riot.  

The Lil’ Remix is designed around 3 inch propellers and 1106 - 1404 motors and provides mounting hole patterns for both 9 and 12 millimeter spacing. It is not recommended to go larger as there hasn’t been any testing with the larger motors and I can’t make any claims of durability.

The Lil’ Remix kit is offered in two versions: the full kit and a “no hardware” version. The full kit provides all the hardware needed to complete your frame minus the 3D printed parts pictured. The “no hardware” leaves out the steel screws, aluminum locknuts,  and the 20mm aluminum standoffs included in the full kit. It does still include the 24mm aluminum standoff as it is an odd size and can be difficult to source elsewhere. To complete the “no hardware” version of the kit you will need:

QTY:  3 20mm aluminum standoffs

QTY:  6 M3x8mm cap head screws

QTY:  4 M3x10mm cap head screws

The files for the optional 3D printed parts shown are available here and will be updated as new parts are designed for the Lil’ Remix frame. At this point I do not have the means to provide printed parts for those that want them and do not have a 3D printer.  I am working on changing that and will update my Facebook and Instagram pages when that changes.

IMPORTANT: Neither version of the kit includes a battery strap and an appropriately sized strap will need to be supplied by the purchaser.

The Lil’ Remix frame is inspired by and serves as a tribute to the 5 inch Remix designed by Tommy Tibajia and manufactured by Rotor Riot.  

The Lil’ Remix is designed around 3 inch propellers and 1106 - 1404 motors and provides mounting hole patterns for both 9 and 12 millimeter spacing. It is not recommended to go larger as there hasn’t been any testing with the larger motors and I can’t make any claims of durability.

The Lil’ Remix kit is offered in two versions: the full kit and a “no hardware” version. The full kit provides all the hardware needed to complete your frame minus the 3D printed parts pictured. The “no hardware” leaves out the steel screws, aluminum locknuts,  and the 20mm aluminum standoffs included in the full kit. It does still include the 24mm aluminum standoff as it is an odd size and can be difficult to source elsewhere. To complete the “no hardware” version of the kit you will need:

QTY:  3 20mm aluminum standoffs

QTY:  6 M3x8mm cap head screws

QTY:  4 M3x10mm cap head screws

The files for the optional 3D printed parts shown are available here and will be updated as new parts are designed for the Lil’ Remix frame. At this point I do not have the means to provide printed parts for those that want them and do not have a 3D printer.  I am working on changing that and will update my Facebook and Instagram pages when that changes.

IMPORTANT: Neither version of the kit includes a battery strap and an appropriately sized strap will need to be supplied by the purchaser.

All the hardware to complete any of the MS series micro quadcopter kits in my store. 

MPORTANT:  This is a carbon only kit. All hardware and accessories will need to be provided by the builder to finish the kit.

Micro quadcopter kit designed around the 11XX brushless motors and 2 inch propellers. It is designed to hold a Runcam Mirco Swift/Swift 2 or similar sized camera with a Eachine VTX03 or similar design video transmitter. The top plate has a cutout to allow for easy viewing or the LED display on the VTX03 video transmitter. The top and bottom plates have chamfered edges and the carbon fiber has been orientated to run parallel to the direction of the arms on the bottom plate.

The frame allows for the mounting of either a 20x20mm flight controller or a smaller 16x16mm one.   The kit requires a single 20mm and 4 15mm standoffs. Three millimeter screws will also need to be supplied by the builder. It is recommended to use a minimum of 8mm long screws for the bottom plate and 6mm long screws for the remainder. A standard sized battery strap will also be required. Using plastic hardware provides for a ~24g frame weight before adding other components.

For 3D printable accessories check out my Thingiverses page to download the files.

This kit is a pair plates to increase the gap between the top and bottom plates on my MS series kits to 20MM. 20MM standoffs will be required to complete the conversion.

IMPORTANT:  This is a carbon only kit. All hardware and accessories will need to be provided by the builder to finish the kit.

Micro quadcopter kit designed around the Flitetest Gremlin power pack. It is designed to hold a Runcam Mirco Swift/Swift 2 or similar sized camera with a Eachine VTX03 or similar design video transmitter. The top plate has a cutout to allow for easy viewing or the LED display on the VTX03 video transmitter. The top and bottom plates have chamfered edges and the carbon fiber has been orientated to run parallel to the direction of the arms on the bottom plate.

The frame allows for the mounting of either a 20x20mm flight controller or a smaller 16x16mm one.   The kit requires a single 20mm and 4 15mm standoffs. Three millimeter screws will also need to be supplied by the builder. It is recommended to use a minimum of 8mm long screws for the bottom plate and 6mm long screws for the remainder. A standard sized battery strap will also be required. Using plastic hardware provides for a ~24g frame weight before adding other components.

2.5 inch propellers should fit this frame as well as the stock Emax propellers included in the power pack.

For 3D printable accessories check out my Thingiverses page to download the files.

IMPORTANT: This is a proof of concept design still at this state. Fit of parts have been confirmed but no durability testing has been performed so no claims are being made. Please take this into account if you puchase this frame.

IMPORTANT: This is a carbon plate only kit. No hardware is included and needs to be provided by purchaser.  A single 20mm and 4 15mm standoffs are required. I recommend using 3mm x 8mm screws for attaching standoffs to the bottom plate and a minimum of 3mm x 6mm screws for the top plate and camera plates.

This Quadcopter kit is designed for 3 inch propellers with either a 12MM or 9MM hole spacing, and a Runcam Micro Swift or similar sized camera. This frame has a cut out in the top plate to accomidate an Eachine VTX03 or similar sized VTX. There may be space for a TBS Unify V2/V3 video transmitter with a dipole or an antenna with a CFL connector but it will be tight.

Both the top and bottom plates have chamfered edges. As well the carbon fiber is aligned to run parallel to the direction of the arms on the 3MM thick bottom plate.

For 3D printable accessories check out my Thingiverses page to download the files.

IMPORTANT: This is a proof of concept design still at this state. Fit of parts have been confirmed but no durability testing has been performed so no claims are being made. Please take this into account if you puchase this frame.

IMPORTANT: This is a carbon plate only kit. No hardware is included and needs to be provided by purchaser. 4-8 20mm standoffs are required for a 20mm plate gap build. A single 20mm and 4-8 15mm standoffs are required for a 15mm build. I recommend using 3mm x 8mm screws for attaching standoffs to the bottom plate and a minimum of 3mm x 6mm screws for the top plate and camera plates.

This Quadcopter kit is designed for 3 inch propellers and a Runcam Micro Swift or similar sized camera. It can be built with a 20mm or 15mm plate gap. There is space for a TBS Unify V2/V3 video transmitter with a dipole or an antenna with a CFL connector.