This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the 2.5" Version

This version is designed to be a small as possible!

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the Compressed X Version

This version uses the 50XX Arm Set on the front and rear, keeping the props as close together as possible front to rear.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the Compressed X Version

This version uses the 50XX Arm Set on the front and rear, keeping the props as close together as possible front to rear.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the Compressed X Version

This version uses the 50XX Arm Set on the front and rear, keeping the props as close together as possible front to rear.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the Stretch X Version with seperate arms

This version uses the 50XXr Arms on the front and rear with the 50XXr Arm Brace, for a race style build.

The Arm Brace must be used with this version!

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

Double stack brushless whoop for a sleek low profile build!

The RotorMunkey Rupee house 2 16mmx16mm stacks in between the motors. With 0703 or 1102 motors there should be plenty clearance below the props for the tiny bit of overlap at the corners. The 2 stacks are space just far enouch apart to accomadate a 16mmx16mm board with a 20mmx20mm outer measurement, such as the tinyFISH FC and tinyPEPPER ESC. 

The upper plate alse has space for a 16x16 board at a 45 degree angle, meaning not only is there space for a vtx such as the Akk X5,  but any 16mmx16mm camera mount will work!

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the True X Version

This version uses the 50XXt Arm Set on the front and rear, keeping the props in a perfect square.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the True X Version

This version uses the 50XXt Arm Set on the front and rear, keeping the props in a perfect square.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the True X Version

This version uses the 50XXt Arm Set on the front and rear, keeping the props in a perfect square.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr

This frame was designed with the Runcam Split mini at the core of the process, as well as a top mounted battery.

The Main Plate is designed to accomadate two seperate 20X20 stacks, allowing for 15mm standoffs while still having space for the Split Mini stack and the FC/ESC. Its going to be a tight build, with 18-20mm clearance between the Main Plate and the Top Plate, depending on arm thickness; however that should be more than enough with the right stacks.

This is the Swept X Version

This version uses the 50XXs Arm Set on the front and 50XXt Arm Set on the rear, to pull the props out of the camera view.

3D Printed parts are neccesary for the build, specifically to mount the Camera.

As Armattan Productions doesn't do 3D parts, check out the whole set on Thingiverse. I've also design the following accesories for the cleanest possible build:

• R-XSR Tray - Mounts under the rear stack, could also fit a smaller RX 
• SMA Mount/Antenna Tube Mount - Slips over the rear standoffs to cleanly manage and SMA pigtail, RX antennas at 90 degrees, and a slot for the Battery lead.
• SMA Mount - no antenna tubes

I have also included some dimensions below, in case you would like to design your own camera mount or other 3d printed parts.

The Maiden frame is available in several configurations:

• Main Plate in 2mm or 3mm
• Top Plate in 1.5mm or 2mm
• 2.5" props with 9mm motor mounts 
• 3" with 12mm motor mounts
• 5" props with 16mm and 19mm motor mounts - Standard (50XX), True X (50XXt), Swept (50XXs), and Stretch X with seperate arms (50XXr)
  • available in 3mm, 4mm, and 5mm
  • 5mm or 6mm for the 50XXr