AOS RC

Kits

  • product
    More Details

    AOS 5 V2 Button Head

    $ 89.99

    This is the button head version. Armattan productions don't supply countersunk hardware so if you want to use the central 30x30mm stack you will need to source  countersunk M3x20mm screws separately. All other stacks can use buttonhead screws.

    The AOS 5 V2 refines and improves upon the original AOS 5 formula. A lightweight 5" frame with exceptional vibration and resonance performance and so much more.
     
    Flight performance is the cornerstone of every AOS frame. Exceptional vibration and resonance performance reduces propwash, oscillations and motor heating. Not only does the AOS 5 V2 fly amazingly on Betaflight 4.3 stock settings it also allows you to push your PID and filter settings further than ever before to achieve unparalleled stick feel and minimal filter delay.
     
    The new arm geometry provides even more stiffness in key directions as well as improved durability in front impact. The 3 screw motor mounting reduces weight and removes the motor hole that can be a stress riser for compressive failure.
     
    The AOS 5 V2 offers unparalleled flexibility for your electronics supporting up to 30x30 mm stacks in the front center and rear. It also supports the DJI Air Unit and HDZero 1W VTX, the original DJI HD FPV camera or any standard micro sized camera.
     
    The AOS 5 V2 features 2 slots for captive battery straps on the top plate as well as an XT60 pass through to keep battery cables away from the props. The GoPro mount uses the AOS standard 32x32mm mounting but includes pre installed press nuts to make mounting a breeze. 
     
    Building the frame couldn't be simpler. Just 8 standoffs and 16 screws are needed and none of the frame screws are shared with your electronics. Only 2 screws need to be undone to change an arm.
     
    Frame specs
    - Designed for up to 5.1 inch props (no props in view)
    - 6 mm Arms
    - 2mm Top Plate and Sandwich Plates
    - 2.5mm Bottom Plate
    - Up to three 30.5x30.5 mm 25.5x25.5 mm or 20x20 mm stacks
    - 32x32mm GoPro mounting holes in top plate with installed press nuts
    - XT60 pass through in top plate
    - Two captive battery strap slots
    - Fits the DJI Air Unit (use front stack mounting) and HDZero 1W VTX
    - Fits the DJI FPV camera or 19x19 mm camera
    - Recommended motor size 2306, 2207, 2208, 25mm
    - 16x16 mm up to 19x19 mm motor mounting
    - Approx. 115g with all hardware
     
    For more info, please make sure to check out https://www.aos-rc.com/
  • product
    More Details

    AOS 5.5 V2 Button Head

    $ 99.99

    This is the button head version. Armattan productions don't supply countersunk hardware so if you want to use the central 30x30mm stack you will need to source  countersunk M3x20mm screws separately. All other stacks can use buttonhead screws.

    The AOS 5.5 V2 refines and improves upon the original AOS 5.5 formula to create the ideal platform for carrying heavier GoPro Hero action cameras. It's not just a lightweight 5.5" frame with exceptional vibration and resonance performance, but so much more.
     
    Flight performance is the cornerstone of every AOS frame. Exceptional vibration and resonance performance reduces propwash, oscillations and motor heating. Not only does the AOS 5.5 V2 fly amazingly on Betaflight 4.3 stock settings; it also allows you to push your PID and filter settings further than ever before to achieve unparalleled stick feel and minimal filter delay.
     
    The new arm geometry provides even more stiffness in key directions as well as improved durability in front impact. The 3 screw motor mounting reduces weight and removes the motor hole that can be a stress riser for compressive failure.
     
    The AOS 5.5 V2 offers unparalleled flexibility for your electronics supporting up to 30x30 mm stacks in the front centre and rear. It also supports the DJI Air Unit and HDZero 1W VTX, the original DJI HD FPV camera or any standard micro sized camera.
     
    The AOS 5.5 V2 features 2 slots for captive battery straps on the top plate as well as an XT60 pass through to keep battery cables away from the props. The GoPro mount uses the AOS standard 32x32mm mounting but includes pre installed press nuts to make mounting a breeze. 
     
    Building the frame couldn't be simpler. Just 8 standoffs and 16 screws are needed and none of the frame screws are shared with your electronics. Only 2 screws need to be undone to change an arm.
     
    Frame specs
    - Designed for up to 5.5 inch props (no props in view)
    - 6 mm Arms
    - 2mm Top Plate and Sandwich Plates
    - 2.5mm Bottom Plate
    - Up to three 30.5x30.5 mm 25.5x25.5 mm or 20x20 mm stacks
    - 32x32mm GoPro mounting holes in top plate with installed press nuts
    - XT60 pass through in top plate
    - Two captive battery strap slots
    - Fits the DJI Air Unit (use front stack mounting) and HDZero 1W VTX
    - Fits the DJI FPV camera or 19x19 mm camera
    - Recommended motor size  2207, 2208, 25mm
    - 16x16 mm up to 19x19 mm motor mounting
    - Approx. 125g with all hardware
     
    For more info, please make sure to check out https://www.aos-rc.com/
  • product
    More Details

    AOS UL5 Button head

    $ 55.99

    Armattan productions doesn't currently supply countersunk hardware so this is the buttonhead version of the frame kit. Countersunk carbon spare parts are available elsewhere in this armattan store.

    The AOS UL5 is an ultralight 5 inch frame optimized for 2-blade props and 2004 and similar size motors. It offers a geometry that has been optimized for vibration and resonance performance with flexible mounting for 30.5x30.5, 25.5x25.5 and 20x20 mm electronics.

    ·     Standoffs, carbon and steel frame screws included

    ·     ~67g with steel hardware

    ·     Designed for 5" biblade props

    ·     5 mm Arms

    ·     1.5 mm Top Plate, Bottom Plate and Sandwich Plates

    ·     One 25.5 or 20 mm mounting up front and one 25.5 or 20 mm mounting in the rear OR One central 30.5, 25.5, 20 mm stack.

    ·     Fits the DJI Caddx Vista perfectly

    ·     Fits 19 mm and 20 mm cameras

    Recommended components:

    ·     2004 motors

    ·     30A or higher toothpick AIO

    ·     Caddx Vista + Nebula Pro

    ·     4S ~800mAh or 6S ~500mAh w/ XT30

    For more info, please make sure to check out https://www.aos-rc.com/
     
  • product
    More Details

    AOS 3.5 V2 Button Head Carbon Only

    $ 44.99

    This is the AOS 3.5 V2 kit. All carbon parts are supplied but no screws or standoffs. Screws required are 8off 6mm M2 button head and 8off 12mm M2 button head. Standoffs required are 8off 20mm M2 standoffs.

    The AOS 3.5 V2 builds on the scientific approach used to design the AOS 5 V2 and AOS 5.5 V2 but brings the target all up weight below 250g. In many regions quadcopters that weigh less than this are not subject to the same burdensome regulations as heavier drones.

     

    With the right components (naked Caddx Vista and 650mAh 4S) the AOS 3.5 V2 can carry an Insta360 GO 2 and still come in under 250g!

     

    But just because a quad cannot weigh more than 250g doesn't mean that we shouldn't strive for the speed, power and agility typically only available from heavier drones. With the right components you can go toe to toe with 5" freestyle quads with similar flingability and smoothness.

     

    A combination of finite element simulation and real-world flight testing gives this frame exceptional vibration and resonance performance. This means you can run less filtering and higher PID gains for a smoother and more responsive feel with greatly improved mid-throttle oscillations and cool motors.

     

    • Approx. 40g with all hardware

    • Designed for up to 3.5 inch props

    • 4 mm Arms

    • One 25.5x25.5 or 20x20 mm stack in the front and one 25.5x25.5 or 20x20 mm stack in the rear OR

    • One 30.5x30.5, 25.5x25.5, or 20x20 mm stack in the centre

    • Fits the Caddx Vista or HDZero 1W Freestyle VTX perfectly

    • Fits both 20mm (DJI camera) and 19mm (Micro sized) cameras

    • Motor mounting 9x9 up to 12x12 (1404, 1505 recommended)

    • Standoffs, frame and motor screws included