Ladies and gentlemen, I give you Pirx Seven! The 7-inch FPV frame designed in-house to give me, and you obviously, a versatile platform for long-range, cinematic takes and freestyle!
Let's begin with the question: why did I have to design my own frame? There are plenty of good frames out there! True, there are good 7-inch frames, but all of them have some problems: props in the view, very little space inside, thin arms, asymmetrical arms, no place for a huge battery, limited accessories and dozens of other minor things.
Pirx Seven overcomes some of them (creates a few others as well, but let's not shout about it) and truth to be told, it's the best 7-inch frame I own. After all, I designed it to solve problems I was having :)
Important notes
FPV camera is mounted on 3D printed bracket by design! During the crash, it's better to break a small 3D printed element than an expensive camera
Verical plates in the front are tight fit by design and have to be precisely sanded/filed to fit slots in the the horizontal plates!
All M3 holes are tight fit by design as well!
Features:
weights around 210g before equipment
dead cat setup, from and rear arms are fully interchangeable
6mm arms are super stiff to shift the resonance frequency high enough to be filtered without interfering with flight performance
4mm bottom plate and 2mm top plate are connected with 12 standoffs in total resulting in pretty nice structural strength and stiffness
accepts ONLY micro size FPV cameras as well as popular micro-split-like cameras like Caddx Tarsier or RunCam Hybrid 4K
will fit DJI FPV Air Unit and camera but there is no mount for the Air Unit ATM
20x20mm holes in the front
30,5x30,5mm and 20x20mm holes in the middle where the center of gravity meets the center of thrust
30,5x30,5mm and 20x20mm holes in the rear section for any equipment you want
has a dedicated place for Matek Optical Flow & Lidar Sensor http://bit.ly/2SSpMcC
accepts LiPo on the top and on the bottom side as well. Top mount is recommended as it moves CoG closer to the thrust plane
variety of 3D printed accessories for cameras and antennas
5-inch hexacopter FPV drones never became a thing. If you want to build one yourself, only for fun, there is nothing on the market. At least until now, since I give you Pirx 56, the 5-inch FPV hexacopter frame that is designed for parts used on FPV quads! No special motors or flight controllers required! Get any Betaflight, INAV, or EmuFlight compatible flight controller with six motor outputs, 6 ESC, six motors, and six propellers, and you are ready to go!
This frame accepts ONLY micro-sized FPV cameras like RunCam Micro Eage, Foxeer Toothless, and similar.
Armattan Productions does not offer 3D printed elements, so to finish your build you will need:
After the success of Pirx Seven 7-inch quadcopter frame, ladies and gentlemen, I decided that I need something similar, but smaller. Still a dead-cat configuration, with plenty of space inside, but more suited for freestyle flight and using five and 5.1-inch propeller.
Pirx5 Freestyle was born!
Accepts ONLY micro size FPV cameras or Caddx Vista with DJI or Nebula camera
Designed for Analog FPV but accepts Caddx Vista digital FPV stack
4mm arms and 4mm main deck
Accepts standard 30,5x30,5mm stack as well as 20x20mm mini-stack
Two additional mounting holes (30,5mm apart) for a half-stack like VTX in the rear
A reinforced front section that acts as a universal HD camera mount
31mm between decks in the center section
25mm between decks in front and rear sections
Designed to carry the LiPo battery on top, but it is possible to put a battery below the main deck
Welcome to our store! Here you'll find the Pirx HD.7 - a sleek and sturdy 7-inch FPV frame that's designed for pilots who demand high-performance and durability.
Crafted from premium quality materials, the Pirx HD.7 frame boasts an impressive strength-to-weight ratio that ensures your drone will survive even the toughest crashes. The frame is specifically designed for use with high-definition cameras, allowing you to capture stunning, crystal-clear footage while you fly.
The Pirx HD.7 features a minimalist design that not only looks great but also helps to reduce air resistance, making it easier to maneuver and control your drone. Its compact size makes it highly portable, so you can take it with you wherever you go.
In addition to its impressive performance and durability, the Pirx HD.7 frame is also highly customizable, allowing you to add your own personal touch to your drone. Whether you're a professional racer or a casual hobbyist, the Pirx HD.7 is the perfect choice for your FPV needs.
Thank you for considering the Pirx HD.7 FPV frame. We're confident that you'll love it as much as we do!
Features:
Suited for both Digital and Analog FPV systems. This includes DJI Air Unit, DJI O3 Air Unit, Caddx Vista, Caddx Avatar and HDzero
Accepts both 30x30 and 20x20 stacks
Designed for 4-in-1 ESC, but can be used with single ESCs on arms
Front bumper gives better crash resistance and give a nice platform to install GoPro Hero 10 or any other HD camera
Flies amazing with Betaflight and INAV
3D printed accessories available in a link below
Can be used as pure breed freestyle, cruiser or long range and cine rig
The Pirx Mini is a "no absurd" simple to build and easy to fly 3" FPV frame.
It has enough space to carry a Caddx Vista or RunCam Link HD FPV link, 20x20 stack and z RX receiver. If you want to, you can build it with analog FPV no problem.