Rhaski - Gallery

Kits

  • product
    More Details

    Phoenix 5inch StretchX v1.1

    $ 54.99

    Image will be updated with new render to show the altered wheelbase soon

    Detailed aesthetic design

    Compact and low profile with 25mm standoffs - can esaily fit 2 board stack, 3 is possible but will be tight

    Space at back of frame for most vtxs to fit easily

    Light weight at approx 100g complete frame weight

    Very durable: 4mm individual arms with quick replacement system (only requires the removal of one bolt, and one more to be loosened a bit), 2mm main plate and 1.5mm top plate and reinforcing bottom plate

    Compatible with a wide range of fpv cameras, and provides good protection to the camera

    Battery can be top or bottom mounted (recommend bottom mount if using a gopro), strap hooks hold a 25mm strap securely in place

    This is the stretch X version of the Phoenix. Wheelbase is narrow accross the roll axis, and elongated on the pitch axis

  • product
    More Details

    Phoenix 5inch TrueX v1.2

    $ 55.45

    The phoenix is a 5" freestyle beast that can kick ass on the track too.

    It is lightweight at around 100g assembled but it can take a serious beating. Several arm designs were tested and broken mercilessly against whitegums, karri trees, bitumen, you name it; until finally the "gecko foot" design proved to be very tough indeed, and only 12mm across the narrowest section to prevent thrust lost and drag.

    The Phoenix has been designed with centre-of-gravity as a priority and this shows in the way it handles; locked in, agile, smooth and fast.

    Field serviceability is another priority, which is why a uniplate design was not adopted. In the unlikely event of an arm breaking, they are individually replaceable, only requiring the removal of one screw, and the loosening of one other. Press nuts have been used for one-tool serviceability.

    In order to maintain a low profile of 25mm (20mm is possible too, these camera plates will be available soon), there is a bay beneath the stack where you can keep your reciever or vtx out of the way, giving you an extra 6mm of effective stack height. The camera protrudes slightly below the bottom of the main plate. This does not put it in harms way as it is not lower than the arms. I have not yet managed to damage a camera in this frame.

    You can mount the battery on top if you run a runcam split, or use a tetragonal battery with a gopro (you'll need a mount, I haven't made one yet), or you can sling the battery underneath and mount the gopro on top. It will be well balanced either way you go.

    Detailed aesthetic design

    Compact and low profile with 25mm standoffs - can esaily fit 2 board stack, 3 is possible

    Space at back of frame for most vtxs to fit easily

    Light weight at approx 90g complete frame weight. Use of titanium/aluminium hardware can bring this down further

    Very durable: 4mm individual arms with quick replacement system (only requires the removal of one bolt, and one more to be loosened a bit), 2mm main plate and 1.5mm top plate and reinforcing bottom plate

    Compatible with a wide range of fpv cameras, and provides good protection to the camera

    Camera angle adjustable between 5 degrees and 60+ degrees

    Battery can be top or bottom mounted (recommend bottom mount if using a gopro), strap hooks hold a 25mm strap securely in place

    3d printed TPU parts such as xt60 holder can be found on thingiverse herre:
    https://www.thingiverse.com/thing:2585149

    Antenna mount can be found on thingiverse here:
    https://www.thingiverse.com/thing:2585152

  • product
    More Details

    Phoenix 5inch TrueX SLAMMED v1.1 20mm Standoffs

    $ 54.99

    Same as the Phoenix 5", but with 20mm standoffs and camera plate to give a lower profile body.

Products

  • product
    More Details

    Phoenix StretchX arm_ALONG THE WEAVE_v1.0

    $ 8.02

    4mm carbon StretchX arms for the 5 inch Phoenix frame. These are a direct swap for the TrueX arms. They provide a narrow roll axis of 140mm and an extended pitch axis of 205mm, giving a total wheelbase of 250mm.

    This provided extra stability on the pitch axis, which many pilots find beneficial for race handling.

    These arms increase the weight by only a few grams and are 13mm at their narrowest point.

  • product
    More Details

    Phoenix 20mm camera plate v1.1 - 1.5mm

    $ 1.62

    Camera plate for 20mm standoff equipped Phoenix 5" fpv quad frame

    v1.1 - minor tweaks to improve front-on impact resilience

  • product
    More Details

    Phoenix 25mm camera plate v1.1 - 1.5mm

    $ 1.62

    Camera plate for 25mm standoff equipped Phoenix 5" fpv quad frame

  • product
    More Details

    Phoenix Main Plate v1.1 - 2.0mm

    $ 8.60

    Version 1.1 of Phoenix 5" fpv quad frame.

    Changes from v1.0:
    -Front standoff screw holes moved slightly aft
    -Camera cutout altered to improve front end collision strength

  • product
    More Details

    Phoenix Top Plate v1.1 - 2mm

    $ 10.00

    Version 1.1 Top plate for Phoenix 5" fpv quad frame

    Changes from v1.0:

    -Upgraded from 1.5mm to 2.0mm for improve strength at the cost of a couple of extra grams

    -Front standoffs moved slightly aft

    -Front forks thickened for improved front on collision strength

  • product
    More Details

    Phoenix Top Plate v1.1 - 1.5mm

    $ 8.54

    Version 1.1 of Top Plate for Phoenix 5" fpv quad frame

    Changes from v1.0

    -Moved front standoffs slightly aft

    -Thickened front forks to improve front collisions strenght

    *Note: this is the 1.5mm version. It is lighter, but not as strong as the 2mm version

  • product
    More Details

    Phoenix TrueX arm 4mm_ALONG THE WEAVE_v1.1

    $ 6.20

    Version 1.1 of the TrueX arm for Phoenix 5" quad frame

    Changes from v1.0:

    - Reduced tolerances on motor bolt pattern

    - Wider "nubs" to protect motor and reduce chance of delamination in heavy crashes

  • product
    More Details

    Bottom Plate 1.5mm v1.1

    $ 5.00

    Bottom plate for v1.1 Phoenix frame

  • product
    More Details

    PHOENIX TRUEX ARM 4MM_CHAMFERED_ALONG THE WEAVE_V1.2

    $ 8.23

    Chamfered TrueX arm for 5" Phoenix.

    This version has had the screw slot replaced with a simple screw hole. While this means that two screws must be removed to replace the arm instead of just one, it significantly strengthens the arm against breaking at that point due to torque acting around the outer bolt in hard collisions. The motor shaft hole has also decreased in radius to further strengthen the end of the arm, though this has not been a weak point since the v1.1 revision, it seemed worth doing anyway.

  • product
    More Details

    PHOENIX STRETCHX ARM 4MM_CHAMFERED_ALONG THE WEAVE_V1.2

    $ 8.23

    This is the Stretch X arm for 5" Phoenix frame, with chamfered edges and cut along hte waeve for durability and stiffness.
    In this revision, the screw slot has been replaced with a simple screw hole to protect against large torque loads acting around the outer arm screw from tearing the inner bolt slot away. While this means it now requires the removal of two screws to replace the arm, it improves durability in high-speed side-impact collisions with the ground or solid objects. The motor shaft hole is also smaller to strengthen the motor bolt pattern even further than in v1.1.