Markus Brandauer
MBx Engineering
Special Quad Frames and spare parts for you!
If you need something special just let me know, I can d.....
Kits
-
Runcam Split Frame 3-inch (with no props in view)
$ 47.92Runcam Split - 3" Frame (with no props in view)
All legal to fly full HD camera Drone (with addional mounting space for GPS)
Designed that no props are in view (Runcam Split v1+2 with GoPro Lens)
Two camera mounting options: 1. hard mounted with the Runcam bracket on the sideplates or 2. with TPU 3D-printed mounts (https://www.thingiverse.com/thing:2975838)
In the package:
- 1x 3mm Baseplate
- 2x 2mm Sideplates
- 2x 2mm Arm Brackets
- 1x 1mm Topplate
- 1x 1mm Backplate
- 3x M3x30mmm Standoff
- 6x M3x6 Aluminium Screws
- 8x M2x8 Screws for Motor mounting with bracket
Info:
- Frameweight: carbon only ~32g | with standoffs and screws: ~39g (if you want to go minimal you can only use baseplate and sideplates at about 29g+additional screws and standoffs)
- Mounting pattern: 30x30mm and 20x20mm
- max. stack height= 26mm
- full protection cage for Runcam Split (from 80° downwards to 90° upward camera angle)
- Motor mounting pattern 12x12mm (2.5mm holes)
- the cuts on the Sideplates - where they fit into the main plate - are intentionally made smaller so that the fit is very tight (if needed just file a little bit out until you can get it in for a strong tight fitting frame)
- if you don't like the additional arm holders you can leave them away. they are just there to make the frame almost undestroyable. The Mainplate is designed to hold up a lot of abouse on its owne. The brackets are just there if someone likes to have them addionally.
cheers MBx
Products
-
TRANSTEC FROG SPARE ARM FRONT AND BACK SLIM 5-INCH 4MM - 16mm Motormount
$ 4.50TransTec Frog Frame 5" Spare Arm
4mm thick, 10.5mm wide, Ø16mm Motormount only.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
TRANSTEC FROG SPARE ARM FRONT AND BACK SLIM 5-INCH 5MM - 16mm Motormount
$ 5.00TransTec Frog Frame 5" Spare Arm
5mm thick, 10.5mm wide - only Ø16mm Motormount Holes
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
Base Plate - 3inch Runcam Split Frame
$ 31.00Baseplate for
Runcam Split - 3" Frame (with no props in view)
-
TRANSTEC FROG SPARE ARM FRONT AND BACK slim 6-inch 4mm
$ 5.10TransTec Frog Frame 6" Spare Arm
4mm thick, 10.5mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
TRANSTEC FROG SPARE ARM FRONT AND BACK SLIM 6-INCH 5MM
$ 5.50TransTec Frog Frame 6" Spare Arm
5mm thick, 10.5mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
TRANSTEC FROG SPARE ARM FRONT AND BACK SLIM 5-INCH 5MM
$ 5.10TransTec Frog Frame 5" Spare Arm
5mm thick, 10.5mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
TRANSTEC FROG SPARE ARM FRONT AND BACK slim 5-inch 4mm
$ 4.50TransTec Frog Frame 5" Spare Arm
4mm thick, 10.5mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.3 with skinny design to save a view grams and motor protection inspired by KababFPV
-
Transtec Frog Frame Top Plate (with antenna mounting options)
$ 3.30Transtec Frog Frame Top Plate with VTX and RX Antenna mounting holes (for zip ties).
-
Top plate - 3inch Runcam Split Frame
$ 2.00Topplate for
Runcam Split - 3" Frame (with no props in view)
https://www.armattanproductions.com/pages/kit_detail/1827
-
Back Plate - 3inch Runcam Split Frame
$ 2.50Backplate for
Runcam Split - 3" Frame (with no props in view)
-
Arm Verstaerkung - 3inch Runcam Split Frame
$ 2.50Arm stiffener plate for
Runcam Split - 3" Frame (with no props in view)
-
-
Runcam Split Frame Sideplate right Countersink - with servo Tilt cam
$ 10.00Runcam Split - 4" Frame with servo Tilt cam
Sideplate right Countersink edition
Runcam Split - 4" Frame with servo Tilt cam
2mm carbon
-
Runcam Split Frame Sideplate left Counterink - with servo Tilt cam
$ 10.00Runcam Split - 4" Frame with servo Tilt cam
Sideplate left Countersink edition
Runcam Split - 4" Frame with servo Tilt cam
2mm carbon
-
Runcam Split Frame Baseplate Countersink - with servo Tilt cam
$ 22.00Runcam Split - 4" Frame with servo Tilt cam
Baseplate Countersink edition
- 3mm carbon
- Mounting pattern: 30.5x30.5mm and 20x20mm
- max. stack height= 27mm
- full protection cage for Runcam Split
- with 9g Servo, Runcam Split 1 or 2, (if needed) seperate tilt controller, GPS, Compass, Baro, 1306 Motors, 4in1 ESC
- AUG weight: 179g(calculated)
- so for under 250g with max. ~70g 2-3s Lipo
- all legal to fly full HD camera GPS Drone
-
Runcam Split Frame Sideplate right with servo Tilt cam
$ 9.50Runcam Split - 4" Frame with servo Tilt cam
Sideplate right
Runcam Split - 4" Frame with servo Tilt cam
2mm carbon
-
Runcam Split Frame Sideplate left with servo Tilt cam
$ 9.50Runcam Split - 4" Frame with servo Tilt cam
Sideplate left
Runcam Split - 4" Frame with servo Tilt cam
2mm carbon
-
Runcam Split Frame Topplate left with servo Tilt cam
$ 4.50Runcam Split - 4" Frame with servo Tilt cam
Topplate
Runcam Split - 4" Frame with servo Tilt cam
1mm carbon
-
Runcam Split Frame Baseplate with servo Tilt cam
$ 21.50Runcam Split - 4" Frame with servo Tilt cam
Baseplate
- 3mm carbon
- Mounting pattern: 30.5x30.5mm and 20x20mm
- max. stack height= 27mm
- full protection cage for Runcam Split
- with 9g Servo, Runcam Split 1 or 2, (if needed) seperate tilt controller, GPS, Compass, Baro, 1306 Motors, 4in1 ESC
- AUG weight: 179g(calculated)
- so for under 250g with max. ~70g 2-3s Lipo
- all legal to fly full HD camera GPS Drone
-
FROG ARM TRANSTEC SPARE ARM FRONT AND BACK ORIGINAL
$ 3.80TransTec Frog Frame 5" Spare Arm
4mm thick, 15.5mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
First batch arrived and tested, fits perfect and finally I got some proper arms with real 4mm carbon on my frog frame.
V.2 with adapted Motor mounting holes.
-
FROG ARM TRANSTEC SPARE ARM FRONT AND BACK LIGHT DESIGN - 2
$ 3.80TransTec Frog Frame 5" Spare Arm
4mm thick, 10mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.2 with adapted Motor mounting holes and a skinny design to save a view grams.
-
FROG ARM TRANSTEC SPARE ARM FRONT AND BACK 1
$ 3.80TransTec Frog Frame 5" Spare Arm
4mm thick, 14mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
V.2 with adapted Motor mounting holes.
-
Frog Arm Transtec Spare Arm Front and Back light Design
$ 3.80TransTec Frog Frame 5" Spare Arm
4mm thick, 10mm wide.
Front and Back enabled with one arm design.
With quick release (only 2 screws per arm) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
First batch arrived and tested, fits perfect and finally I got some proper arms with real 4mm carbon on my frog frame.
V.2 with adapted Motor mounting holes and a skinny design to save a view grams.
-
Frog Arm Transtec Spare Arm Front and Back
$ 3.80TransTec Frog Frame 5" Spare Arm
4mm thick, 15.5mm wide.
Front and Back enabled with one arm design.
With quick release for M3 zylindrical head screw (Ø5mm head) - so you dont have to remove the Flightcontroller stack screws everytime you change an Arm. Just screw from the upper plate to the stack and leave the second plate beyond to sandwich the arms.
First batch arrived and tested, fits perfect and finally I got some proper arms with real 4mm carbon on my frog frame.
V.2 with adapted Motor mounting holes.