HB Designs
Products
-
HB lightning 92 4mm - 16x16mm
$ 11.28FC mount holes: m2 16x16mm
Motor Mount holes: m2 9mm spacing (11XX series motors)
Max Propeller size: 2.5in
Motor to motor 92mm
Estimated weight: 6gramsPlate, i.e. arms are 4mm thick, they're taller than they're wide for aerodynamics. (Similar to vertical arm carbon)
Recommended for lighter 2S setups using 16x16mm towers.
optional 3D printed canopy will be shortly avaiable. -
HB lightning 87 4mm 20x20mm FC mount
$ 10.30FC mount holes: m2-m3 20x20mm
Motor Mount holes: m2 9mm spacing (11XX series motors)
Max Propeller size: 2in
Motor to motor 87mm
Estimated weight: 7gramsPlate, i.e. arms are 4mm thick, they're taller than they're wide for aerodynamics. (Similar to vertical arm carbon frames)
Recommended for high powered 2-4S setups using 20x20mm towers.
optional 3D printed canopy will be shortly available.
-
HB lightning 113 5mm
$ 14.64FC mount holes: m2-m3 20x20mm
Motor Mount holes: m2 9mm spacing (11XX series motors)
Max Propeller size: 3in
Motor to motor 113mm
Estimated weight: 8gramsPlate, i.e. arms are 5mm thick, they're taller than they're wide for aerodynamics. (Similar to vertical arm carbon)
Recommended for high powered 2-4S setups using 20x20mm towers.
optional 3D printed canopy will be shortly avaiable. -
HB Aero 113 4mm (20x20mm fc mount)
$ 12.82FC mount holes: m2-m3 20x20mm
Motor Mount holes: m2 9mm spacing (11XX series motors)
Max Propeller size: 3in
Motor to motor 113mm
Estimated weight: 9.5gramsThis design pushes boundary a little less and is slightly over cautious in arm sizing to maximize durability. Plate, i.e. arms are 4mm thick.
Recommended for high powered 2-4S setups using 20x20mm towers.
optional 3D printed canopy will be shortly avaiable.
-
HB Vertigo Duo 200 (5in)
$ 39.99NOTE: 2 plates needed! - The special design has extra thin arms, designed to have (2) 5mm plates stacked together for a low drag vertical style arm.
motor and FC bolts are sufficient for lighter builts, but recommend CA (Super Glue), between the 2 plates for heavier builds.
3x plates can be used for even more strength!
FC mount holes: m2-m3 30.5x30.5mm OR m2-m3 20x20mm
Motor Mount holes: m3 16mm + 19mm spacing (more 22xx, 23xx series motors)
Max Propeller size: 5in (5.5inch propeller capable)
Motor to motor 200mm
Estimated weight: 28grams (56grams for 2 plate stack)Recommended for high power ratio by reducing weight.
This frame is designed for use with any 30.5x30.5mm top plate, or 3D printed canopies.
optional 3D printed canopy will be shortly available.
-
HB UL185 5mm Delux
$ 31.60Delux version has chamfered edges and countersunk holes on main FC mount screws.
FC mount holes: m2-m3 20x20mm
Motor Mount holes: m3 12mm spacing (e.g. 13xx, 14xx series motors)
Max Propeller size: 5in
Motor to motor 185mm
Estimated weight: 22gramsThis design pushes boundaries and is recommended for high power ratios via lighter components.
Example: 1306 3100kv motors, 5in 5040 props, 20x20mm 4in1 Esc with 20x20mm FC tower stack. 450mah 3s battery
This frame is designed for use with any 20x20mm top plate, or 3D printed canopies.
optional 3D printed canopy will be shortly available.
-
Top Plate for All HB frames with 20x20mm FC mount pattern
$ 3.12Top Plate for All HB frames with 20x20mm FC mount pattern
Use with 4 aluminum standoffs for ultra light but tough camera and electronics protection.
Or go crazy with 4 nylon standoffs and nylon screws for more weight saving.
-
-
-
