Kenneth- Gallery

Image

Ken's CAD Models is committed to bring new and relevant product to market serving the hobbyist's as well as commercial needs.

Kits

  • product
    More Details

    SPLAT 150

    $ 18.81

    The SPLAT 150 is designed for 3" propellers, and can take 1104-1804 motors. With 32mm standoffs it will accommodate a Sony HS1177 Super HAD II FPV camera, CC3D or NAZE32 FC stacked on top of a power distribution board. The arms are wide enough to hold down the escs, directing the wires the shortes possible distance to the flight controller.

     

    Note: This is still in the prototype stage.

  • product
    More Details

    RoboWarrior Division 12lb Sumobot

    $ 169.54

    These compoonents represent the Carbon Fiber parts only of a larger Bill of Materials required to complete this 12lb Sumobot.

Products

  • product
    More Details

    Splat 150 Main Frame

    $ 14.93

    This is the main frame for a 150 class quadcopter. Unlike many that are made from 3mm material, I have chosen 2mm for it. The smaller and lighter these machines become, the less mass is need to be "bullet proof". The frame is sized to accept a NAZE32, CC3D, or CC3D Atom flight controller, and 35mm x 35mm Power Distribution Board.

    With 30mm standoffs (4 req.), there is room for a 1/3 SONY Super HAD II CCD camera.

    Motor arms will accept 1104 - 1306 motors with a four bolt circle of  9-12mm diameter.

    10A ESCs will fit on the arm between the motors and flight controller.

    3" diameter is the maximum propeller size.

  • product
    More Details

    Splat 150 Upper Frame

    $ 4.86

    This is the complimentary component for the SPLAT 150 Main Frame. The split end is the front and the .060" dia. holes just behind it are for mounting a 1/3 SONY Super HAD II CCD camera on its standard bracket with its supplied screws. There is room for a sattelite Rx and Vtx on this plate and is the intended position for them.

  • product
    More Details

    Plate Lower 3mm CF x1

    $ 39.10

    This is the Lower Plate for my teams 2018 RWD competition entry. Only one is required of 3mm carbon fiber.

  • product
    More Details

    Plate Upper 3mm CF x1

    $ 39.10

    This is the Upper Plate for my teams 2018 RWD competition entry. Only one is required of 3mm carbon fiber.

  • product
    More Details

    Plate Side Inner 3mm CF x2

    $ 22.58

    This is the Plate Side Inner for my teams 2018 RWD competition entry. Only two are required of 3mm carbon fiber.

  • product
    More Details

    Fork Arm Bracket 3mm CF x4

    $ 5.84

    This bracket reinforces the connection between the Fork Lift Arm and the Fork Down Leg. 4 pieces required.

  • product
    More Details

    Fork Jack Body Mount 3mm CF x2

    $ 3.81

    This is the mount for the base of the Jack Tube to the Main Body. 2 pieces required.

  • product
    More Details

    Fork Arm Pivot 3mm CF x4

    $ 4.20

    This is part of the hard mounting for the offensive capabilities for the Sumobot. 4 pieces are required.

  • product
    More Details

    Fork Arm Pivot V2 3mm CF x4

    $ 3.86

    This is an alternative Fork Arm Pivot Bracket. It has additional mounting tabs for articulated claws at the front.

  • product
    More Details

    Fork Lift Pivot 3mm CF x4

    $ 4.70

    This is a new bracket for the lift point on the fork assembly. It is a significant improvement in speed at which the fork travels up and down as well as providing 90 degrees of fork travel.