Quad 66

Image

Design, build, fly, repeat.

Products

  • product
    More Details

    Piglet 115 (2mm)

    $ 15.60

    The Piglet takes the Gen4 WarPig frame and puts the 3 hole mount on the ends of the arms. This frame is intended 1102 builds. 

    Frame: 115 mm MTM, 2 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation (will work with with two screws)

    Motor: 3 hole (standard whoop size)

    Props: 2.5 inch 65mm

    Canopy: Printed or Zip-tie Canopy 

    Weight: 4.2 gm (estimated)

  • product
    More Details

    WarPig 110 V4.1 (2.5mm)

    $ 13.92

    The WP 110 is intended for 2S 2 inch. The 2.5mm thickness to get a little more torsional rigidity. This small change helps reduce noise getting to the gyro allowing less filtering and associated latency. 

    Version 4.1 slightly increases the strength at the middle of the motor mount.

    Frame: 110 mm MTM, 2.5 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation (will work with with two screws)

    Motor: 2 mm on 9 mm diameter

    Props: 2 inch

    Canopy: Zip-tie Canopy or the new Printed canopy.(see the canopy tab for the file https://ko-fi.com/quad66/shop)

    Weight (aproximate): 4.4 gm

  • product
    More Details

    WarPIg 115 V4.1 (3mm)

    $ 16.30

    The 115 is my personal favorite. It is intended for 2S 2.5 inch props. The 115 size give just enough room to keep the camera low and keep the area under the props clear with 2S 300 mah packs. The 3mm frame is thicker than typically seen for this size to control the resonance without resorting to braces/struts that add material obstructing the props and like to hang up in trees.

    Version 4.1 slightly increases the strength at the middle of the motor mount.

    Frame: 115 mm MTM, 3 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation 

    Motor: 2 mm on 9 mm diameter

    Props: 2.5 inch

    Canopy: Zip-tie Canopy or the new Printed canopy.(see the canopy tab for the file https://ko-fi.com/quad66/shop)

    Weight (aproximate): 5.8 gm

  • product
    More Details

    WARPIG 124 V4.1 (4MM)

    $ 24.28

    The WarPig 124 4 mm is optimzed for 3 inch 3 S builds and at home in parks and more open spaces. The 124 has a larger foot print that than 120 so the props are a little further out to keep the thrust clean. The 4 mm thickness adds durability and helps reduce noise getting to the gyro allowing high PIDs with low filters which maximize performance.

    Frame: 124 mm MTM, 4 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation 

    Motor: 2 mm on 9 mm diameter

    Props: 3 inch

    Canopy: Zip-tie Canopy or the new Printed canopy.(see the canopy tab for the file in my ko-fi shop )

    Weight: 8.8 gm (aproximately)

  • product
    More Details

    WarPig 120 v4.1.1 (2.5 mm)

    $ 15.60

    The WP 120 2.5mm is the 1S 3 inch specialist. For these builds I've gone up from 2mm up to 2.5mm thickness to get a little more torsional rigidity. This small change helps reduce noise getting to the gyro allowing less filtering and associated latency. The 120 has a slightly smaller footprint than the 124 as the 1S builds are best suited for smaller backyard spaces. 

    Version 4.1 slightly increases the strength at the middle of the motor mount.

    Frame: 120 mm MTM, 2.5 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation

    Motor: 2 mm on 9 mm diameter

    Props: 3 inch

    Canopy: Zip-tie Canopy or the new Printed canopy.(see the canopy tab for the file https://ko-fi.com/quad66/shop)

    Weight (aproximate): 5.3 gm

  • product
    More Details

    WarPig 120 v4.1.1 (3 mm)

    $ 15.04

    The WP 120 3mm is for robust 1S 3 inch or ultralight 2-3 S bilds. The 120 has a slightly smaller footprint than the 124 as the and is best suited for smaller backyard spaces. 

    Version 4.1 slightly increases the strength at the middle of the motor mount.

    Frame: 120 mm MTM, 3 mm thick

    FC: 16 x 16 stack, 25.5 x 25.5 AIO square orienation, 25.5 x 25.5 AIO whoop orientation 

    Motor: 2 mm on 9 mm diameter

    Props: 3 inch

    Canopy: Zip-tie Canopy or the new Printed canopy.(see the canopy tab for the file https://ko-fi.com/quad66/shop)

    Weight (aproximate): 6.4 gm

  • product
    More Details

    SkyRyder 90 (1.5 mm)

    $ 8.88

    The SR 90 is an ultralight frame for converting whoops to open prop 2 inch builds. In particular, the Gemfan 2015 biblade props are highly recommended. The frame is kept at 1.5mm so that you can use the regular motor mount screws and not have to go hunting for longer screws. To keep vibrations and noise in check, the arms are kept relatively wide and short to push any resonance into higher frequencies where it can be handled by the filtering

    Frame: 90 mm MTM, 1.5 mm thick

    FC: 25.5 x 25.5 AIO whoop orientation 

    Motor: 1.4 mm on 6.6 mm diameter

    Props: 2 inch

    Canopy: whoop

    Weight (approximate): 2.4 gm